Chevrolet Automobile Parts 2001 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hochdruckreiniger Chevrolet Automobile Parts 2001 herunter. Chevrolet Automobile Parts 2001 User's Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 20
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet4.7 / 5. Basierend auf33 Kundenbewertungen
Seitenansicht 0
POWER RACK & PINION
2001 Chevrolet Camaro
2000-01 STEERING
Power Rack & Pinion
Cars - Except Prizm & Saturn
MODEL IDENTIFICATION
BODY CODE IDENTIFICATION
Body Code Model
"C" .................................................... Park Avenue
"E" ....................................................... Eldorado
"F" .............................................. Camaro & Firebird
"G" ......................................................... Aurora
"H" ........................................... Bonneville & LeSabre
"J" ............................................. Cavalier & Sunfire
"K" .............................................. DeVille & Seville
"N" ....................................... Alero, Grand Am & Malibu
"W" ................. Century, Grand Prix, Impala, Intrigue, Lumina,
Monte Carlo & Regal
"Y" ....................................................... Corvette
DESCRIPTION & OPERATION
NOTE: Some vehicles are equipped with Variable Effort Steering
(VES) system, identified by a solenoid on the power steering
pump at the pressure line outlet. See appropriate ELECTRONIC
article.
RACK & PINION ASSEMBLY
Pump pressurizes fluid and sends it through the pump’s flow
control valve to the pinion and valve on the rack and pinion assembly.
See Fig. 1. Pinion and valve direct fluid to either side of the piston
and rack, depending on turning direction of steering wheel. Piston and
rack converts hydraulic pressure into linear force, reducing turning
effort.
POWER STEERING PUMP
Two types of power steering pumps are used, CB series or TC
series. These pumps are constant displacement vane-type pumps. See
Fig. 4 and Fig. 5. When pressure exceeds set limits, a flow control
pressure relief valve opens, allowing fluid to return to the inlet
side of the pump. Some pump applications have remote fluid reservoirs
or reservoir attached to pump assembly, to enable different pump
mounting locations. Some models have a reverse rotation pump,
depending upon location and belt routing.
LUBRICATION
FLUID TYPE
Use GM Power Steering Fluid (1050017). Failure to use proper
fluid will cause hose and seal damage, resulting in fluid leaks and
Seitenansicht 0
1 2 3 4 5 6 ... 19 20

Inhaltsverzeichnis

Seite 1 - POWER RACK & PINION

POWER RACK & PINION 2001 Chevrolet Camaro 2000-01 STEERING Power Rack & Pinion Cars - Except Prizm & Saturn

Seite 2

NOTE: Pump is not serviceable on Seville. Disassembly 1) Remove hydraulic union fitting (or VES actuator) frompump. See Fig. 4. Rem

Seite 3 - PRESSURE TEST

Disassembly 1) Remove pump pulley. See POWER STEERING PUMP PULLEY underREMOVAL & INSTALLATION. Remove shaft bearing retaining rin

Seite 4 - FLOW RATE TEST

Fig. 5: Exploded View Of Power Steering Pump (TC Series)Courtesy of General Motors Corp.Fig. 6: Measuring Shaft Bearing Clearance (TC Series)Courtes

Seite 5 - OUTER TIE ROD

Fig. 7: Installing Bearing & Retaining Ring (TC Series)Courtesy of General Motors Corp. RACK & PINION

Seite 6 - PUMP SHAFT SEAL

NOTE: Perform overhaul procedures with rack and pinion assembly removed from vehicle. See RACK & PINION ASSEMBLY underREMOVAL & INS

Seite 7

Clean valve body ring grooves. Check pinion and valveassembly drive pin. If pin is broken, replace rack and pinionassembly. Reassembl

Seite 8

Fig. 9: Installing Valve Body RingsCourtesy of General Motors Corp.

Seite 9 - OVERHAUL

Fig. 10: Setting Valve Body RingsCourtesy of General Motors Corp. INNER TIE ROD Disassembly 1) Remove outer tie rod end from

Seite 10

of turns required for removal. Remove hex jam nut from inner tie rod.Remove adjusting nut from inner tie rod. Remove outer boot clamp. Cutoff and disc

Seite 11

TORQUE SPECIFICATIONSApplication Ft. Lbs. (N.m)Adjuster Plug Lock Nut Magnasteer ...

Seite 12

damage to pump and/or rack and pinion assembly. CAPACITYPOWER STEERING FLUID CAPACITYApplication Pump Capacity Sys

Seite 14

vehicle, ensuring steering wheel returns to center after turning.Fig. 1: Exploded View Of Power Rack & Pinion Steering Assembly(Typical)Courtesy

Seite 15

record highest pressure displayed each time valve is closed. Ifreadings are as specified and within 50 psi (4 kg/cm) of each other,go to step 6). See

Seite 16

REMOVAL & INSTALLATIONCAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveabili

Seite 17 - INNER TIE ROD

end of shaft. To complete installation, reverse removal procedure.Fill and bleed hydraulic system. See HYDRAULIC SYSTEM BLEEDING underLUBRICATION.

Seite 18

Removal (CB Series Pump) Remove power steering pump (if necessary to allow clearancefor pulley removal). See POWER STEERING PUMP. Rem

Seite 19

frame, and remove rear engine frame-to-body mounting bolts. Ensurerear of engine frame can be lowered without damaging other components.Separate steer

Seite 20

steering coupler pinch bolts and remove coupler from rack and pinion. 2) Raise and support vehicle. Remove front wheels. Disconnectand separat

Kommentare zu diesen Handbüchern

Keine Kommentare