Chevrolet Air Conditioner Camaro Bedienungsanleitung PDF herunterladen (Seite 9)

harness connector terminal B2 (Dark Blue wire) and C1 (Purple wire).

Turn ignition switch to ON position. Set mode selector switch to VENT

position. Place blower motor switch in low speed position. If blower

motor operates, go to step 8). If blower motor does not operate, go to

step 7).

5) Check for poor connection or connector damage at blower

switch harness connector. Repair or replace as necessary. After

repair, go to step 20). If connection is okay, go to next step.

6) Replace blower motor switch. See BLOWER MOTOR SWITCH under

REMOVAL & INSTALLATION. After repair, go to step 20).

7) Leave jumper wire connected as described in step 4). Turn

ignition switch to OFF position. Disconnect blower motor harness

connector. Turn ignition switch to ON position. Connect test light

between blower motor harness connector terminals "A" (Black wire) and

"B" (Purple wire). If test light illuminates, go to step 11). If test

light does not illuminate, go to step 10).

8) Check for poor connection at blower motor relay harness

connector. Repair or replace as necessary. After repair, go to step

20). If connection is okay, go to next step.

9) Replace blower motor relay. After repair, go to step 20).

10) Leave jumper wire connected. Using test light connected

to ground, probe blower motor harness connector terminal "B" (Purple

wire). If test light illuminates, go to step 14). If test light does

not illuminate, go to step 13).

11) Check for poor connection or connector damage at blower

motor harness connector. Repair or replace as necessary. After repair,

go to step 20). If connection is okay, go to next step.

12) Replace blower motor. See BLOWER MOTOR under REMOVAL &

INSTALLATION. After repair, go to step 20).

13) Repair open or poor connection in Purple wire between

blower motor relay harness connector terminal C1 and blower motor

harness connector terminal "B". After repair, go to step 20).

14) Repair open or poor connection in Black wire between

ground and blower motor harness connector terminal "A". After repair,

go to step 20).

15) Using test light connected to ground, probe A/C-heater

control panel harness connector C2 terminal "C" (Brown wire). If test

light illuminates, go to next step. If test light does not illuminate,

go to step 19).

16) Check for open circuit or poor connection between A/C-

heater control panel harness connector C2 terminals "B" (Light Green

wire) and "C" (Brown wire). See WIRING DIAGRAMS. Repair or replace as

necessary. After repair, go to step 20). If no problem is found, go to

next step.

17) Check for poor connection(s) or connector damage at A/C-

heater control panel switch harness connectors. Repair or replace as

necessary. After repair, go to step 20). If connections are okay, go

to next step.

18) Replace A/C-heater control panel. See

A/C-HEATER CONTROL PANEL under REMOVAL & INSTALLATION. After repair,

go to step 20).

19) Check for poor connection or wire damage in Brown wire

between A/C-heater control panel harness connector C2 terminal "C" and

HVAC fuse (20-amp) located in instrument panel fuse block. Repair or

replace as necessary. After repair, go to next step.

20) Operate blower system to verify repair. If blower motor

operates normally, repair is complete. If blower motor is still

inoperative, return to step 3).

2001 Models

1) Perform DIAGNOSTIC SYSTEM TEST. Go to next step.

2) Turn ignition switch to ON position. Set mode selector

switch to VENT position. Place blower motor switch in each speed

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Chevrolet Air Conditioner Camaro Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Autos Chevrolet Air Conditioner Camaro