Wire Harness Installation Instructions For Installing: #20110 Classic Customizable Chevy II/Nova 1966-67 Harness 21 Circuit Manual #
7.1.2 Attach harness groups to your vehicle with clips or ties (provided with this kit) starting at the fuse block and working your way out to the
7.3.4 If you have a fiberglass body you should install a terminal black to ground all your gauges and accessories. Ground the Terminal Block and ev
8.2 TAIL/DOME SECTION CONNECTIONS 8.2.1 Take the DOME LIGHT SECTION and route it up from behind the drivers side kick pane
8.2.3 Take the Tail Harness and route it from the drivers kick panel down the door jamb toward the rear of the vehicle. R
8.2.4 Locate the wire for the fuel sending unit and route it as shown in Figure 8.8. Connect the wire to the sending
8.2.5 Locate the wire for the license plate light in the harness and route it through the grommet going out of the trunk. Connect the wire to the
8.3 ENGINE SECTION CONNECTIONS 8.3.1 Route the wiper motor, coil, choke, temp sender, oil sender, starter, alternator and a/c compressor wires a
8.3.3 Locate the maxi fuse holder and mount it to the passenger side inner fender panel as shown in figure 8.13. Take the starter Red wire (916) an
Figure 8.15 Alternator Connections Note: In with the kit you should find a connector with a Blue and a White wire labeled
8.4 HEADLIGHT SECTION CONNECTIONS 8.4.1 Route the headlight, park light, horn and electric fan wires down the inner fender panel to the hor
We have attempted to provide you with as accurate instructions as possible, and are always concerned about corrections or improvements that can b
8.4.7 Take the headlight ground ring terminal and ground it using one of the bolts in the core support. 8.5 DASH SECT
Figure 8.21 Turn Switch Connector Removal Figure 8.22 Turn Switch Connector Pin-out 8.5.4 You will need to remove and use the turn signal switch
Figure 8.23 Steering Column Covered for Protection Figure 8.24 Instrument Panel Connections 8.5.6 Just down from the turn switch wires you will
Figure 8.25 Ignition Switch Connector 8.5.12 Reinstall the instrument panel. 8.5.13 Before re-installing the column drop collor, take and install
Table 10.1 Fuse Requirements 9.0 TESTING THE SYSTEM 9.0.1 Use a small battery charger (10 amp or less) to power up the vehicle for circuit test
10.2 WIRE CONNECTION INDEX Color Ga. No. Connect to Wire Starting Point Section of Starting Point HEADLIGHT SECTION Grn 14 924 Horn Horn R
Table 10.2 Wire Connection Index (2 of 3) 21 Color Ga. No. Connect to Wire Starting Point Section of Starting Point HEADLIGHT SWITCH SEC
Color Ga. No. Connect to Wire Starting Point Section of Starting Point WIPER SWITCH SECTION Blu 4 18 986 Wiper Switch Wiper Motor Wiper Motor
The wiper switch connector is no longer available. We have terminated the wiper switch wires with the correct terminals so that your original con
NOTES 23
NOTE : If your vehicle has an existing harness, you will want to retain it for the possible re-use of various Pigtails & Co
Painless Performance Limited Warranty and Return Policy Chassis harnesses, fuel injection harnesses and Striker ColdShot units are covered under a
TABLE OF CONTENTS List of Figures.………………………………………………………………………… ii List of Tables.…………………………………………………………………………. ii 1.0 Introduction……………
LIST OF FIGURES Figure 3.1 The Painless Performance Wire Harness Kit (Part #20110)………………………. 2 Figure 5.1 Engine and Front Harness…………………………………
1.0 INTRODUCTION You have purchased what we at Perfect Performance Products, LLC, believe to be the easiest to install automotive wire harness on
3.0 CONTENTS OF THE PAINLESS PERFORMANCE WIRE HARNESS KIT (PART #20110) Refer to Figure 3.1 to take inventory. See that you have all the parts yo
4.0 TOOLS NEEDED In addition to your regular tools, you will need, at least, the following tools: Crimper tool Note: Use a quality tool to avo
6.0 PRE-INSTALLATION AND GENERAL HARNESS ROUTING GUIDELINES
Kommentare zu diesen Handbüchern